| Item |
Offence |
Section |
Set Fine |
| 0.1 |
Fail to ensure all equipment used in drilling a well is in good condition and adequate. |
3.1 (a) |
$500.00 |
| 0.2 |
Fail to prevent the migration of oil, gas or water from one horizon to another. |
3.1 (b) |
$750.00 |
| 0.3 |
Fail to properly handle or dispose of all fluids produced or recovered |
3.1 (c) |
$500.00 |
| 0.4 |
Fail to properly handle or dispose of fluids or refuse from a well |
3.1 (d) |
$500.00 |
| 1. |
Drill a well with a surface location in a restricted drilling area |
3.1.1 |
$400.00 |
| 2. |
Fail to construct sumps or pits or to provide tanks prior to spudding |
3.2 |
$400.00 |
| 3. |
Fail to install temporary fencing around sump |
3.2.1 (a) |
$200.00 |
| 4. |
Fail to install a impervious liner |
3.2.1 (b) |
$200.00 |
| 5. |
Fail to maintain fluid levels 0.5 metres below base of dike |
3.2.1 (c) |
$200.00 |
| 6. |
Fail to use proper liner in earthen sump or pit |
3.2.2 |
$200.00 |
| 7. |
Fail to close earthen sump or pit within 6 months of TD date |
3.3 |
$500.00 |
| 8. |
Fail to isolate formations from contamination caused by migration of fluids |
3.4 (c) |
$750.00 |
| 9. |
Fail to prevent migration of fluids to surface or sub-surface |
3.4 (d) |
$750.00 |
| 10. |
Fail to prevent shale and unconsolidated material from falling into open hole during drilling |
3.4 (e) |
$250.00 |
| 11. |
Improper removal of casing during drilling |
3.5.1 |
$450.00 |
| 12. |
Improper removal of casing from a producing well |
3.5.1.1 |
$450.00 |
| 13. |
Fail to have proper hole size for casing when sealing well |
3.5.2 |
$250.00 |
| 14. |
Fail to have proper annular clearance between casings |
3.5.3 |
$250.00 |
| 15. |
Fail to record history of used casing |
3.6 (a) |
$400.00 |
| 16. |
Fail to examine condition of thread on pipe and inside collars of used casings |
3.6 (b) |
$400.00 |
| 17. |
Fail to examine condition of pipe near threads and casing collars of used casings |
3.6 (c) |
$400.00 |
| 18. |
Fail to conduct wall thickness measurements on joints of used casings |
3.6 (d) |
$400.00 |
| 19. |
Fail to conduct a hydrostatic pressure test on used casings |
3.6 (e) |
$400.00 |
| 20. |
Fail to guide casing properly into hole |
3.7 (a) |
$250.00 |
| 21. |
Fail to apply correct casing torque or thread standoff |
3.7 (b) |
$250.00 |
| 22. |
Fail to clean threads and examine casing |
3.7 (c) |
$250.00 |
| 23. |
Fail to examine and clear casing of internal obstructions |
3.7 (d) |
$250.00 |
| 24. |
Fail to use thread compound on casing joints |
3.7 (e) |
$250.00 |
| 25. |
Fail to pressure test all joints in the string |
3.7 (f) |
$250.00 |
| 26. |
Fail to protect all potable water formations |
3.9 (a) |
$700.00 |
| 27. |
Fail to protect potential hydrocarbon-bearing zones |
3.9 (b) |
$700.00 |
| 28. |
Fail to protect casings from fluid bearing formations |
3.9 (c) |
$400.00 |
| 28.1 |
Fail to meet cement quality |
3.9.2(a) |
$750.00 |
| 28.2 |
Fail to comply with API publication for selecting correct cement grade |
3.9.2(b) |
$750.00 |
| 28.3 |
Fail to ensure cement correctly mixed and pumped |
3.9.2(b) |
$500.00 |
| 29. |
Fail to ensure cement quality by providing Examiner on site |
3.9.2 (c) |
$450.00 |
| 30. |
Fail to run conductor casing where water flows occur close to surface |
3.10 |
$450.00 |
| 31. |
Fail to ensure conductor casing is of sufficient weight and quality |
3.10.1 (a) |
$450.00 |
| 32. |
Fail to ensure hole is dry and monitored prior to resumption of drilling |
3.10.1 (b) |
$450.00 |
| 33. |
Fail to squeeze cement to isolate fresh water zone where water flow not stopped |
3.10.1 (c) |
$450.00 |
| 34. |
Recover conductor casing prior to cementing next string |
3.10.1 (d) |
$450.00 |
| 35. |
Fail to permanently isolate and protect potable water |
3.11 (a) |
$500.00 |
| 36. |
Fail to prevent cross-flow between fluid bearing zones |
3.11 (b) |
$500.00 |
| 37. |
Fail to prevent sloughing of unconsolidated material into well bore |
3.11 (c) |
$500.00 |
| 38. |
Fail to anchor well control equipment |
3.11 (d) |
$500.00 |
| 39. |
Fail to cement surface casing |
3.11.1 |
$500.00 |
| 40. |
Fail to drill surface hole sufficiently deep into bedrock |
3.11.2 |
$500.00 |
| 41. |
Fail to run a string of casing above the artesian fresh water zone |
3.11.3 |
$500.00 |
| 42. |
Fail to cement surface casing before drilling |
3.11.4 |
$500.00 |
| 43. |
Fail to cement surface casing full length |
3.11.4 (a) |
$500.00 |
| 44. |
Fail to use proper excess cement volume |
3.11.4 (b) |
$500.00 |
| 45. |
Fail to cement surface casing using circulation method |
3.11.4 (c) |
$500.00 |
| 46. |
Fail to monitor annular flow for cement returns |
3.11.5 |
$500.00 |
| 47. |
Fail to ensure surface casing cement complies with API Specification 10 |
3.11.6 |
$500.00 |
| 48. |
Fail to ensure surface casing cement retains 5 metres of tail cement |
3.11.7 |
$500.00 |
| 49. |
Fail to pre-flush before pumping cement into casing |
3.11.8 |
$500.00 |
| 50. |
Fail to obtain slurry samples during cementing operation |
3.11.9 |
$500.00 |
| 51. |
Fail to determine WOC (Wait on Cement) time |
3.11.10 |
$500.00 |
| 52. |
Commence drill-out operation before cement attains 3600 kPa compressive strength |
3.11.10 |
$500.00 |
| 53. |
Fail to conduct casing pressure test before cement drilled out of shoe joint |
3.11.11 |
$500.00 |
| 54. |
Fail to conduct remedial work if casing fails pressure test |
3.11.11 |
$500.00 |
| 55. |
Fail to conduct pressure integrity test |
3.11.12 |
$500.00 |
| 56. |
Fail to use a low volume, high pressure pump for pressure integrity test |
3.11.12 (a) |
$500.00 |
| 57. |
Apply incorrect pressure during pressure integrity test |
3.11.12 (a) |
$500.00 |
| 58. |
Fail to conduct pressure integrity test for ten minutes |
3.11.12 (b) |
$500.00 |
| 59. |
Fail to use an incompressible fluid in pressure integrity test |
3.11.12 (c) |
$500.00 |
| 60. |
Fail to record test data in pressure integrity test |
3.11.12 (d) |
$500.00 |
| 61. |
Fail to conduct remedial work when casing seat fails pressure integrity test |
3.11.13 |
$500.00 |
| 62. |
Fail to use intermediate casing and cement to protect equipment and formations from excessive pressures |
3.12 (a) |
$500.00 |
| 63. |
Fail to use intermediate casing and cement to prevent fluid migration |
3.12 (b) |
$500.00 |
| 64. |
Fail to use intermediate casing and cement to prevent material from falling into open hole |
3.12 (c) |
$500.00 |
| 65. |
Fail to control the target zone pressure |
3.12 (d) |
$500.00 |
| 66. |
Fail to set and cement intermediate casing prior to drilling |
3.12.1 |
$500.00 |
| 67. |
Fail to cement casing when aquifer is present |
3.12.2 |
$500.00 |
| 68. |
Fail to identify all oil, gas and fluid bearing zones when drilling |
3.12.3 (a) |
$500.00 |
| 69. |
Fail to pump cement to separate all oil, gas and fluid bearing zones |
3.12.3 (b) |
$500.00 |
| 70. |
Fail to ensure cement in casing annulus rises 25 metres above previous casing seat |
3.12.3 (c) |
$500.00 |
| 71. |
Fail to provide an Examiner to certify isolation of all porous zones |
3.12.3 (d) |
$550.00 |
| 72. |
Fail to seal or plug the lost circulation zone prior to or during the cementing of the casing |
3.12.4 |
$500.00 |
| 73. |
Fail to cement by circulation method to 25 metres above last casing seat |
3.12.5 |
$500.00 |
| 74. |
Fail to conduct remedial cementing to isolate all porous zones |
3.12.5.1 |
$500.00 |
| 75. |
Fail to utilize correct cement volume |
3.12.6 |
$500.00 |
| 76. |
Fail to use sulphate-resistant casing cement |
3.12.7 |
$500.00 |
| 77. |
Fail to run 5 metre long shoe joint |
3.12.8 |
$500.00 |
| 78. |
Fail to wait on cement for 6 hours before starting drill-out operation |
3.12.9 |
$500.00 |
| 79. |
Fail to conduct casing pressure test before cement drilled out of shoe joint |
3.12.10 |
$500.00 |
| 80. |
Fail to conduct a low pressure test before cement drilled out of shoe joint |
3.12.10 (a) |
$500.00 |
| 81. |
Fail to conduct a high pressure test before cement drilled out of shoe joint |
3.12.10 (b) |
$500.00 |
| 82. |
Fail conduct remedial work where casing fails pressure test |
3.12.10 |
$500.00 |
| 83. |
Fail to install and test spool, casing valve and BOP equipment with intermediate casing string |
3.12.11 |
$500.00 |
| 84. |
Fail to conduct pressure integrity test after drilling cement in shoe joint |
3.12.12 |
$650.00 |
| 85. |
Fail to use low volume, high pressure pump in pressure integrity test |
3.12.12 (a) |
$650.00 |
| 86. |
Fail to apply proper pressure on formation in pressure integrity test |
3.12.12 (b) |
$650.00 |
| 87. |
Fail to apply pressure for 10 minutes in pressure integrity test |
3.12.12 (c) |
$650.00 |
| 88. |
Fail to use incompressible fluid in pressure integrity test |
3.12.12 (d) |
$650.00 |
| 89. |
Fail to record type and gradient of incompressible fluid in pressure integrity test |
3.12.12 (e) (i) |
$200.00 |
| 90. |
Fail to record duration of pressure integrity test |
3.12.12 (e) (ii) |
$200.00 |
| 91. |
Fail to record initial pressure in pressure integrity test |
3.12.12 (e) (iii) |
$200.00 |
| 92. |
Fail to record final pressure in pressure integrity test |
3.12.12 (e) (iv) |
$200.00 |
| 93. |
Fail to protect equipment and formations with cemented production casing |
3.13 |
$400.00 |
| 93.1 |
Fail to run a gamma ray log within 30 days of well’s TD date |
3.13.1(a) |
$700.00 |
| 93.2 |
Fail to run a neutron log within 30 days of well’s TD date |
3.13.1(b) |
$700.00 |
| 93.3 |
Fail to install all wellhead equipment in compliance with API Spec 6A |
3.13.2 |
$700.00 |
| 94. |
Fail to install a well control device capable of closing around the cable prior to drilling |
3.13.4 (a) (i) |
$700.00 |
| 95. |
Fail to install a well control device with remote controls |
3.13.4 (a) (ii) |
$700.00 |
| 96. |
Fail to perform daily function test of well control device |
3.13.4 (b) |
$500.00 |
| 97. |
Fail to ensure all lubricator components can handle pressure |
3.13.4 (c) |
$500.00 |
| 98. |
Fail to specify when lubricator system is employed |
3.13.4 (d) |
$500.00 |
| 99. |
Fail to use full lubricator system |
3.13.4 (e) |
$500.00 |
| 100. |
Fail to properly install rotary head to BOP system |
3.13.5 |
$500.00 |
| 101. |
Fail to cement production casing 25 metres above previous casing seat |
3.13.6 |
$500.00 |
| 102. |
Fail to cement production casing 25 metres above corrosive zone |
3.13.6 (a) |
$500.00 |
| 103. |
Fail to cement production casing liner over its full length |
3.13.6 (b) |
$500.00 |
| 104. |
Fail to cement production casing to surface in wells located in water-covered areas |
3.13.6 (d) |
$500.00 |
| 105. |
Fail to provide an Examiner to certify cement tops |
3.13.6 |
$450.00 |
| 106. |
Fail to isolate porous zones by remedial cementing |
3.13.6.1 |
$400.00 |
| 107. |
Fail to use 30 per cent excess volume of cement based on theoretical calculation |
3.13.7 (a) |
$400.00 |
| 108. |
Fail to use 20 per cent excess volume of cement based on calliper volume determination |
3.13.7 (b) |
$400.00 |
| 109. |
Fail to use proper quality and temperature of water when mixing cement |
3.13.8 (a) |
$400.00 |
| 110. |
Fail to run a 5 metre casing shoe joint to retain tail cement |
3.13.8 (b) |
$400.00 |
| 111. |
Fail to cement by displacement method and use a wiper plug to separate cement |
3.13.9 (a) |
$400.00 |
| 112. |
Fail to provide a positive stop to cement displacement |
3.13.9 (b) |
$400.00 |
| 113. |
Fail to remove drilling fluid and filter cake and improve cement bond |
3.13.9 (c) |
$400.00 |
| 114. |
Fail to use wall cleaners or scratchers to improve cement bond |
3.13.9 (d) |
$400.00 |
| 115. |
Fail to run centralizers at proper locations |
3.13.10 |
$400.00 |
| 116. |
Fail to pump sufficient volume of neat tail cement |
3.13.11 (a) |
$400.00 |
| 117. |
Fail to ensure tail cement is equal in quality to neat cement |
3.13.11 (b) |
$400.00 |
| 118. |
Fail to use remedial cementing techniques where potential for hydrostatic communication between formations |
3.13.12 |
$400.00 |
| 119. |
Fail to retain records of remedial cementing |
3.13.13 |
$200.00 |
| 119.1 |
Fail to run cement bond log |
3.13.13 |
$700.00 |
| 119.2 |
Fail to comply with API Spec 6A for surface equipment |
3.14 |
$700.00 |
| 120. |
Fail to install a casing head or spool prior to completing well |
3.14 (a) |
$400.00 |
| 121. |
Fail to provide a wellhead to isolate the annulus at surface prior to completing well |
3.14 (b) |
$400.00 |
| 122. |
Fail to install a tubing head or tubing spool prior to completing well |
3.14 (c) |
$400.00 |
| 123. |
Drilling and cementing records — fail to keep on file the size, type, grade and weight of casing |
3.15 (a) |
$200.00 |
| 124. |
Drilling and cementing records — fail to keep on file the names of the manufacturer and supplier |
3.15 (b) |
$200.00 |
| 125. |
Drilling and cementing records — fail to keep on file a casing tally |
3.15 (c) |
$200.00 |
| 126. |
Drilling and cementing records — fail to keep on file whether casing was new or used |
3.15 (d) |
$200.00 |
| 127. |
Drilling and cementing records — fail to keep on file the history of use for used casing |
3.15 (e) |
$200.00 |
| 128. |
Drilling and cementing records — fail to keep on file the setting depth |
3.15 (f) |
$200.00 |
| 129. |
Drilling and cementing records — fail to keep on file description of operational problems while running casing |
3.15 (g) |
$200.00 |
| 130. |
Drilling and cementing records — fail to keep on file the cementing company name |
3.16 (a) |
$200.00 |
| 131. |
Drilling and cementing records — fail to keep on file the cement blends used |
3.16 (b) |
$200.00 |
| 132. |
Drilling and cementing records — fail to keep on file the source of mix water |
3.16 (c) |
$200.00 |
| 133. |
Drilling and cementing records — fail to keep on file type and volume of any preflush |
3.16 (d) |
$200.00 |
| 134. |
Drilling and cementing records — fail to keep on file volumes of cement |
3.16 (e) |
$200.00 |
| 135. |
Drilling and cementing records — fail to keep on file cement slurry density |
3.16 (f) |
$200.00 |
| 136. |
Drilling and cementing records — fail to keep on file actual displacement volume |
3.16 (g) |
$200.00 |
| 137. |
Drilling and cementing records — fail to keep on file final displacement pressure |
3.16 (h) |
$200.00 |
| 138. |
Drilling and cementing records — fail to keep on file any cement movement techniques |
3.16 (i) |
$200.00 |
| 139. |
Drilling and cementing records — fail to keep on file cement returns with estimate of volume |
3.16 (j) |
$200.00 |
| 140. |
Drilling and cementing records — fail to keep on file float equipment and casing attachments |
3.16 (k) |
$200.00 |
| 141. |
Drilling and cementing records — fail to keep on file results of every pressure test |
3.16 (l) |
$200.00 |
| 142. |
Drilling and cementing records — fail to keep on file cement tops and their identification |
3.16 (m) |
$200.00 |
| 143. |
Drilling and cementing records — fail to keep on file description of any operational problems |
3.16 (n) |
$200.00 |
| 144. |
Drilling and cementing records — fail record and keep on file a copy of cement bond logs |
3.16 (o) |
$200.00 |
| 145. |
Fail to keep on site records that include depth at start of day or shift |
3.17 (a) |
$200.00 |
| 146. |
Fail to keep on site records that include depth at end of day or shift |
3.17 (b) |
$200.00 |
| 147. |
Fail to keep on site records that include diameter of the hole |
3.17 (c) |
$200.00 |
| 148. |
Fail to keep on site records that include any change in casing program |
3.17 (d) |
$200.00 |
| 149. |
Fail to keep on site records that include setting depth, casing size, type, grade and weight |
3.17 (e) |
$200.00 |
| 150. |
Fail to keep on site records that include new or used casing |
3.17 (f) |
$200.00 |
| 151. |
Fail to keep on site records that include a description of all cement jobs |
3.17 (g) |
$200.00 |
| 152. |
Fail to keep on site records that include pressure tests and results |
3.17 (h) |
$200.00 |
| 153. |
Fail to keep on site records that include the depth of all shows of oil, gas or water |
3.17 (i) |
$200.00 |
| 154. |
Fail to keep on site records that include the depth of lost circulation zones |
3.17 (j) |
$200.00 |
| 155. |
Fail to keep on site records that include a description of related operations |
3.17 (k) |
$200.00 |
| 156. |
Drilling samples — fail to collect at 3 metre intervals from vertical or deviated portion of wellbore |
3.18 (a) (i) |
$250.00 |
| 157. |
Drilling samples — fail to collect at 6 metre intervals from horizontal portion of wellbore |
3.18 (a) (ii) |
$250.00 |
| 158. |
Drilling samples — fail to bag, dry and label sample bags |
3.18 (b) (i) |
$250.00 |
| 159. |
Drilling samples — fail to wash, dry and label sample vials |
3.18 (b) (ii) |
$250.00 |
| 160. |
Drilling samples — fail to provide samples recovered from a well |
3.18 (c) |
$250.00 |
| 161. |
Site rehabilitation — fail to clear area around well of all refuse material |
3.19 (a) |
$700.00 |
| 162. |
Site rehabilitation — fail to dispose of all liquid and solid waste in a safe manner |
3.19 (b) |
$700.00 |
| 163. |
Site rehabilitation — fail to fill in excavations |
3.19 (c) |
$700.00 |
| 164. |
Site rehabilitation — fail to clean pits of salt and chemicals that inhibit plant growth |
3.19 (d) |
$700.00 |
| 165. |
Site rehabilitation — fail to remove concrete bases, machinery and materials |
3.19 (e) |
$500.00 |
| 166. |
Site rehabilitation — fail to level and restore site to original condition |
3.19 (f) |
$500.00 |
| 167. |
Site rehabilitation — fail to provide an Examiner to visit site and certify rehabilitation and plugging properly completed |
3.19 (g) |
$450.00 |
| 167.1 |
Commence drilling in Lake Erie prior to April 1 or after October 31 |
3.20 (a) |
N.S.F. |
| 168. |
Water covered area — fail to cement all casings to lake bed |
3.20 (b) |
$700.00 |
| 169. |
Water covered area — fail to monitor for oil and liquid hydrocarbons |
3.20 (c) |
$500.00 |
| 170. |
Water covered area — fail to use fresh water drilling fluids only |
3.20 (e) |
$500.00 |
| 171. |
Water covered area — fail to have onboard tanks to contain all drilling fluids |
3.20 (f) |
$500.00 |
| 172. |
Water covered area — fail to reduce turbidity when returning drill cuttings to lake bed |
3.20 (g) |
$400.00 |
| 173. |
Water covered area — fail to prepare and submit contingency plan |
3.20.1 |
$400.00 |
| 174. |
Water covered area — fail to include emergency definitions in contingency plan |
3.20.1 (a) |
$400.00 |
| 175. |
Water covered area — fail to include written instructions for response and mitigation in contingency plan |
3.20.1 (b) |
$400.00 |
| 176. |
Water covered area — fail to include emergency response organizations and responsibilities for actions in contingency plan |
3.20.1 (c) |
$400.00 |
| 177. |
Water covered areas — fail to include locations, access routes or directions to all works in contingency plan |
3.20.1 (d) |
$400.00 |
| 178. |
Water covered areas — fail to list resources, supplies and equipment required for response and mitigation in contingency plan |
3.20.1 (e) |
$400.00 |
| 179. |
Water covered areas — fail to include contact lists for personnel, public bodies and equipment suppliers in contingency plan |
3.20.1 (f) |
$400.00 |
| 180. |
Water covered areas — fail to include incident assessment and reporting procedures in contingency plan |
3.20.1 (g) |
$400.00 |
| 181. |
Water covered areas — fail to conduct regular emergency response drills |
3.20.2 |
$400.00 |
| 182. |
Fail to install and maintain adequate BOP equipment during drilling |
4.1 |
$700.00 |
| 183. |
Fail to have proper flanges on casing bowl or spool to which BOP attached |
4.4.1 (a) |
$700.00 |
| 184. |
Fail to have at least one valve on casing bowl or spool to which BOP equipment attached |
4.4.1 (b) |
$700.00 |
| 185. |
Fail to connect BOP to an accumulator system where hydraulic operation |
4.4.3 |
$400.00 |
| 186. |
Fail to locate wheel used to close blowout preventer 5 metres from rig floor and to secure shaft to preventer where mechanical operation of BOP |
4.4.4 |
$400.00 |
| 187. |
Fail to install and operate accumulator system to manufacturer’s specifications |
4.4.5 (a) |
$400.00 |
| 188. |
Fail to ensure accumulator can provide fluid of sufficient volume and pressure |
4.4.5 (b) |
$400.00 |
| 189. |
Fail to connect accumulator properly to BOP |
4.4.5 (c) |
$400.00 |
| 190. |
Fail to ensure accumulator system is recharged by pump |
4.4.5 (d) |
$400.00 |
| 191. |
Fail to ensure accumulator system can close ram blowout preventer within 30 seconds |
4.4.5 (e) |
$400.00 |
| 192. |
Fail to ensure accumulator system can close annular blowout preventer within 90 seconds |
4.4.5 (f) |
$400.00 |
| 193. |
Fail to ensure accumulator system is equipped with gauges |
4.4.5 (g) |
$400.00 |
| 194. |
Fail to ensure accumulator system is equipped with check valve |
4.4.5 (h) |
$400.00 |
| 195. |
Fail to ensure nitrogen supply is connected to accumulator system |
4.4.6 |
$400.00 |
| 196. |
Fail to have adequate nitrogen supply |
4.4.6 (a) |
$400.00 |
| 197. |
Fail to maintain nitrogen supply at 12,500 kPa |
4.4.6 (b) |
$400.00 |
| 198. |
Fail to install or have available pressure gauge to measure nitrogen pressure |
4.4.6 (c) |
$400.00 |
| 199. |
Fail to install hand wheels on ram preventers |
4.4.7 |
$400.00 |
| 200. |
Fail to install operating controls for hydraulically operated BOP system |
4.4.8 |
$400.00 |
| 201. |
Kill systems — fail to install an inlet below BOP |
4.4.9 |
$400.00 |
| 202. |
Kill systems — fail to install proper size inlet below BOP |
4.4.9 (a) |
$400.00 |
| 203. |
Kill systems — fail to install nipple, valve and kill line for Class B wells |
4.4.9 (b) |
$400.00 |
| 204. |
Kill systems — fail to install kill line components with proper pressure rating |
4.4.9 (c) |
$400.00 |
| 205. |
Kill systems — fail to install separate lines for kill fluids |
4.4.9 (d) |
$400.00 |
| 206. |
Bleed-off system — fail to install bleed-off outlet below BOP |
4.4.10 |
$400.00 |
| 207. |
Bleed-off system — fail to install proper size outlet |
4.4.10 (a) |
$400.00 |
| 208. |
Bleed-off system — fail to install proper nipple, valve and bleed-off line for Class B wells |
4.4.10 (b) |
$400.00 |
| 209. |
Bleed-off system — fail to have proper pressure rating for bleed-off line |
4.4.10 (c) |
$400.00 |
| 210. |
Bleed-off system — fail to attach separate lines to named equipment |
4.4.10 (d) |
$400.00 |
| 211. |
Flexible hose — fail to install hose with proper pressure rating |
4.4.11 (a) |
$400.00 |
| 212. |
Flexible hose — fail to install hose with proper internal diameter |
4.4.11 (b) |
$400.00 |
| 213. |
Flexible hose — fail to install hose with factory installed connections |
4.4.11 (c) |
$400.00 |
| 214. |
Flexible hose — fail to install hose with adequate fire protection sheath |
4.4.11 (d) |
$400.00 |
| 215. |
Flexible hose — fail to install hose with manufacturer’s identification |
4.4.11 (e) |
$400.00 |
| 216. |
Flexible hose — fail to install flexible hose with bends equal to or greater than manufacturer’s specifications |
4.4.11 (f) |
$400.00 |
| 217. |
Flexible hose — fail to secure flexible hose |
4.4.11 (g) |
$400.00 |
| 218. |
Flexible hose — fail to shop service and test |
4.4.11 (h) |
$400.00 |
| 219. |
Flexible hose — fail to record test and maintenance data |
4.4.11 (h) |
$400.00 |
| 220. |
Fail to conduct a pressure test prior to drilling cement out |
4.4.12 |
$400.00 |
| 221. |
Fail to test BOP equipment daily |
4.4.13 |
$700.00 |
| 222. |
Fail to service defective BOP equipment |
4.4.13 |
$700.00 |
| 223. |
Fail to shop service BOP equipment every 3 years |
4.4.14 |
$700.00 |
| 224. |
Fail to record test and maintenance data of BOP equipment |
4.4.14 |
$400.00 |
| 225. |
Training — fail to ensure rig crew is trained |
4.4.15 (a) |
$700.00 |
| 226. |
Training — fail to ensure that driller is certified |
4.4.15 (b) |
$700.00 |
| 227. |
Training — fail to ensure that at least one person is certified |
4.4.15 (c) |
$700.00 |
| 228. |
Training — fail to ensure that BOP drills are performed prior to drilling |
4.4.15 (d) |
$400.00 |
| 229. |
Training — fail to ensure that BOP drills are performed every seven days |
4.4.15 (e) |
$400.00 |
| 230. |
Training — fail to ensure that BOP drills are recorded |
4.4.15 (f) |
$400.00 |
| 231. |
Training — fail to post kick control procedures at rig |
4.4.15 (g) |
$400.00 |
| 232. |
Fail to use Class A well BOP equipment |
4.5.1 (a) |
$500.00 |
| 233. |
Fail to use Class B well BOP equipment |
4.5.1 (b) |
$500.00 |
| 234. |
Fail to properly construct drilling-through components |
4.5.2 |
$400.00 |
| 235. |
Fail to have flange as part of casing bowl |
4.5.3 (a) |
$400.00 |
| 236. |
Fail to ensure casing bowl has one valve |
4.5.3 (b) |
$400.00 |
| 237. |
Fail to ensure blowout preventer is hydraulically operated |
4.5.4 |
$400.00 |
| 238. |
Fail to install and operate accumulator system to manufacturer’s specifications |
4.5.5 (a) |
$400.00 |
| 239. |
Fail to ensure accumulator system maintains pressure |
4.5.5 (b) |
$400.00 |
| 240. |
Fail to ensure accumulator system is connected to blowout preventers |
4.5.5 (c) |
$400.00 |
| 241. |
Fail to ensure accumulator system is recharged by automatic pump |
4.5.5 (d) |
$400.00 |
| 242. |
Fail to ensure accumulator system can close ram blowout preventer |
4.5.5 (e) |
$400.00 |
| 243. |
Fail to ensure accumulator system can close annular blowout preventer |
4.5.5 (f) |
$400.00 |
| 244. |
Fail to ensure accumulator system can close annular blowout preventer |
4.5.5 (g) |
$400.00 |
| 245. |
Fail to ensure accumulator system is equipped with fittings and gauges |
4.5.5 (h) |
$400.00 |
| 246. |
Fail to connect accumulator to nitrogen supply |
4.5.6 |
$400.00 |
| 247. |
Fail to have adequate nitrogen supply to operate BOP equipment |
4.5.6 (a) |
$400.00 |
| 248. |
Fail to have nitrogen supply at 12,500 kPa |
4.5.6 (b) |
$400.00 |
| 249. |
Fail to install or have available gauge to measure nitrogen pressure |
4.5.6 (c) |
$400.00 |
| 250. |
Fail to have hand wheels for ram type blowout preventers |
4.5.7 |
$400.00 |
| 251. |
Fail to include operating controls for each blowout preventer |
4.5.8 (a) |
$400.00 |
| 252. |
Fail to include additional controls to close and open valve |
4.5.8 (b) (i) |
$400.00 |
| 253. |
Fail to include additional controls 15 metres from well |
4.5.8 (b) (ii) |
$400.00 |
| 254. |
Fail to include readily accessible and protected additional controls |
4.5.8 (b) (iii) |
$400.00 |
| 255. |
Fail to include a kill system |
4.5.9 |
$400.00 |
| 256. |
Fail to have proper pressure rating of kill system |
4.5.9 (a) |
$400.00 |
| 257. |
Fail to include kill line connecting mud line to drilling spool |
4.5.9 (b) |
$400.00 |
| 258. |
Fail to include a valved kill system to isolate kill line from stand pipe |
4.5.9 (c) |
$400.00 |
| 259. |
Fail to include kill system with two flanged valves on drilling spools |
4.5.9 (d) |
$400.00 |
| 260. |
Fail to include kill system with 50 millimetres diameter |
4.5.9 (e) |
$400.00 |
| 261. |
Fail to install flexible hose with proper pressure rating |
4.5.10 (a) |
$400.00 |
| 262. |
Fail to install flexible hose with proper diameter |
4.5.10 (b) |
$400.00 |
| 263. |
Fail to install flexible hose with proper connections |
4.5.10 (c) |
$400.00 |
| 264. |
Fail to install flexible hose with proper sheathing |
4.5.10 (d) |
$400.00 |
| 265. |
Fail to install flexible hose with proper markings |
4.5.10 (e) |
$400.00 |
| 266. |
Fail to install flexible hose with proper bending radius |
4.5.10 (f) |
$400.00 |
| 267. |
Fail to secure flexible hose |
4.5.10 (g) |
$400.00 |
| 268. |
Fail to shop service flex hose every 3 years |
4.5.10 (h) |
$400.00 |
| 269. |
Fail to record flexible hose test and maintenance data |
4.5.10 (h) |
$400.00 |
| 270. |
Fail to ensure Class B bleed-off system valves have proper pressure rating |
4.5.11 (a) |
$400.00 |
| 271. |
Fail to ensure Class B bleed-off system contains only straight pipe or 90 degree bends |
4.5.11 (b) |
$400.00 |
| 272. |
Fail to ensure Class B bleed-off system is securely tied down |
4.5.11 (c) |
$400.00 |
| 273. |
Fail to ensure Class A bleed-off system has proper line with valve |
4.5.12 (a) |
$400.00 |
| 274. |
Fail to ensure Class A bleed-off system has proper line to pit 30 metres from well |
4.5.12 (b) |
$400.00 |
| 275. |
Fail to ensure Class A bleed-off line is 75 millimetres in diameter |
4.5.13 (a) |
$400.00 |
| 276. |
Fail to ensure Class A bleed-off line is connected by proper flanges and unions |
4.5.13 (b) |
$400.00 |
| 277. |
Fail to ensure Class A bleed-off line contains 2 valves on drilling spool |
4.5.13 (c) |
$400.00 |
| 278. |
Fail to ensure Class A bleed-off line flexible hose conforms to standards |
4.5.13 (d) |
$400.00 |
| 279. |
Fail to ensure choke-manifold is properly constructed |
4.5.14 (a) |
$400.00 |
| 280. |
Fail to ensure choke-manifold permits flow from well to flare pit |
4.5.14 (b) (i) |
$400.00 |
| 281. |
Fail to ensure choke-manifold permits flow from well to lines of proper diameter |
4.5.14 (b) (ii) |
$400.00 |
| 282. |
Fail to ensure choke-manifold contains two adjustable chokes |
4.5.14 (c) |
$400.00 |
| 283. |
Fail to ensure choke-manifold is constructed with valved outlet |
4.5.14 (d) |
$400.00 |
| 284. |
Fail to ensure choke-manifold provides casing pressure |
4.5.14 (e) |
$400.00 |
| 285. |
Fail to ensure choke-manifold is constructed to provide flow paths |
4.5.14 (f) |
$400.00 |
| 286. |
Fail to ensure choke-manifold is located outside sub-structure |
4.5.14 (g) |
$400.00 |
| 287. |
Fail to ensure choke-manifold is protected from freezing |
4.5.14 (h) |
$400.00 |
| 288. |
Fail to ensure mud system line is connected to choke line |
4.5.14.1 (a) |
$400.00 |
| 289. |
Fail to ensure proper diameter of mud system line |
4.5.14.1 (b) |
$400.00 |
| 290. |
Fail to ensure mud system line directs flow through mud-gas separator |
4.5.14.1 (c) |
$400.00 |
| 291. |
Fail to ensure bleed-off line from choke manifold to flare pit is proper diameter |
4.5.14.2 (a) |
$400.00 |
| 292. |
Fail to ensure bleed-off line from choke manifold to flare pit is 30 meters from well |
4.5.14.2 (b) |
$400.00 |
| 293. |
Fail to ensure bleed-off line from choke manifold is in downward direction to earthen pit of 1 metre |
4.5.14.2 (c) (i) |
$400.00 |
| 294. |
Fail to ensure walls of earthen pit where choke manifold bleed-off line terminates have proper height |
4.5.14.2 (c) (ii) |
$400.00 |
| 295. |
Fail to ensure earthen pit where choke manifold bleed-off line terminates is shaped to contain liquid |
4.5.14.2 (c) (iii) |
$400.00 |
| 296. |
Fail to ensure auxiliary choke manifold bleed-off lines have proper diameter |
4.5.14.3 |
$400.00 |
| 297. |
Fail to install and maintain a mud-gas separator in mud tank |
4.5.15 (a) |
$400.00 |
| 298. |
Fail to install and maintain a warning device in mud tank |
4.5.15 (b) |
$400.00 |
| 299. |
Fail to equip drilling mud system with device to measure volume |
4.5.16 |
$400.00 |
| 300. |
Fail to ensure hole is filled with proper amount of fluid when pulling pipe from well |
4.5.17 (a) |
$400.00 |
| 301. |
Fail to ensure volume of fluid in hole is recorded when pulling pipe from well |
4.5.17 (b) |
$400.00 |
| 302. |
Fail to ensure heat is provided to blow out preventer |
4.5.18 (a) |
$400.00 |
| 303. |
Fail to ensure bleed-off lines are empty in cold weather |
4.5.18 (b) (i) |
$400.00 |
| 304. |
Fail to ensure bleed-off lines are filled with non-freezing fluid in cold weather |
4.5.18 (b) (ii) |
$400.00 |
| 305. |
Fail to ensure bleed-off lines are heated in cold weather |
4.5.18 (b) (iii) |
$400.00 |
| 306. |
Fail to install and maintain drill string safety valve and a device capable of stopping back flow |
4.5.19 |
$400.00 |
| 307. |
Air, gas or foam drilling — fail to install and maintain a rotating head |
4.5.20 (a) (i) |
$400.00 |
| 308. |
Air, gas or foam drilling — fail to install and maintain a 30 metre diverter line |
4.5.20 (a) (ii) |
$400.00 |
| 309. |
Air, gas or foam drilling — fail to install and maintain a reserve volume of drilling fluid |
4.5.20 (a) (iii) |
$400.00 |
| 310. |
Air, gas or foam drilling — fail to install and maintain a hydrogen sulphide monitor |
4.5.20 (a) (iv) |
$400.00 |
| 311. |
Air, gas or foam drilling — fail to flare any gas flowing from diverter line |
4.5.20 (b) |
$400.00 |
| 312. |
Fail to ensure pressure test on casing and ram type preventer |
4.5.21 (a) |
$400.00 |
| 313. |
Fail to ensure pressure test on casing, ram and annular type preventer |
4.5.21 (b) |
$400.00 |
| 314. |
Fail to ensure pressure test on casing, ram preventer and bleed-off manifold |
4.5.21 (c) |
$400.00 |
| 315. |
Fail to ensure pressure test on casing and each annular preventer |
4.5.21 (d) |
$400.00 |
| 316. |
Fail to cease operation when pressure tests not satisfactory |
4.5.21.1 |
$400.00 |
| 317. |
Fail to run a casing inspection log |
4.5.22 (a) |
$400.00 |
| 318. |
Fail to run a pressure test at weakest section of casing |
4.5.22 (b) |
$400.00 |
| 319. |
Fail to test BOP equipment daily |
4.5.23 (a) |
$400.00 |
| 320. |
Fail to properly test annular type BOP equipment |
4.5.23 (b) |
$400.00 |
| 321. |
Fail to record BOP tests |
4.5.23 (c) |
$400.00 |
| 322. |
Fail to service BOP equipment |
4.5.24 |
$400.00 |
| 323. |
Fail to ensure rig crew is trained in the operation of BOP equipment |
4.5.25 (a) |
$700.00 |
| 324. |
Fail to ensure driller has First Line Supervisor certificate |
4.5.25 (b) |
$700.00 |
| 325. |
Fail to ensure at least one person has Second Line Supervisor certificate |
4.5.25 (c) |
$700.00 |
| 326. |
Fail to ensure blowout prevention drills conducted prior to drilling |
4.5.25 (d) |
$500.00 |
| 327. |
Fail to ensure blowout prevention drills conducted every 7 days |
4.5.25 (e) |
$500.00 |
| 328. |
Fail to ensure drills are recorded |
4.5.25 (f) |
$400.00 |
| 329. |
Fail to ensure device allows circulation of fluids through drill string |
4.5.26 (a) |
$400.00 |
| 330. |
Fail to install remote control master valve on testing head |
4.5.26 (b) |
$400.00 |
| 331. |
Fail to ensure well is under control |
4.6 (a) |
$700.00 |
| 332. |
Fail to ensure blowout prevention is installed and maintained |
4.6 (b) |
$500.00 |
| 333. |
Fail to ensure blowout prevention equipment is installed to specifications |
4.6 (c) |
$500.00 |
| 334. |
Fail to ensure blowout prevention pressure rating is proper |
4.6 (d) |
$500.00 |
| 335. |
Fail to ensure ram preventers have hand wheels |
4.6 (e) |
$400.00 |
| 336. |
Fail to meet Class II servicing requirements |
4.6 (f) |
$400.00 |
| 337. |
Fail to install and operate accumulator system to manufacturers specifications |
4.6.4 (a) |
$400.00 |
| 338. |
Fail to connect accumulator system to preventer with lines of proper pressure |
4.6.4 (b) |
$400.00 |
| 339. |
Fail to ensure accumulator system is capable of providing sufficient pressure and volume |
4.6.4 (c) |
$400.00 |
| 340. |
Fail to ensure accumulator system is recharged by pressure controlled pump |
4.6.4 (d) |
$400.00 |
| 341. |
Fail to ensure accumulator capable of closing ram type preventer within 30 seconds |
4.6.4 (e) |
$400.00 |
| 342. |
Fail to ensure accumulator system is capable of closing annular preventer within 60 seconds |
4.6.4 (f) |
$400.00 |
| 343. |
Fail to ensure accumulator system is equipped with proper gauges and fittings |
4.6.4 (g) |
$400.00 |
| 344. |
Fail to ensure accumulator system is equipped with check valve |
4.6.4 (h) |
$400.00 |
| 345. |
Fail to connect accumulator system to nitrogen supply |
4.6.5 |
$400.00 |
| 346. |
Fail to ensure nitrogen supply provides sufficient volume and pressure |
4.6.6 (a) |
$400.00 |
| 347. |
Fail to ensure nitrogen supply has gauge to determine pressure |
4.6.6 (b) |
$400.00 |
| 348. |
Fail to have operating controls readily accessible and at 5 metres from well for Class I and II wells |
4.6.7 (b) |
$400.00 |
| 349. |
Fail to have an independent accumulator system with proper controls for Class III wells |
4.6.8 (a) |
$400.00 |
| 350. |
Fail to have additional set of controls for Class III wells |
4.6.8 (b) |
$400.00 |
| 351. |
Class I BOP system — fail to have diverter system with proper lines |
4.6.8.1 (a) |
$400.00 |
| 352. |
Class I BOP system — fail to have a shut-off valve in bottom joint of tubing |
4.6.8.1 (b) |
$400.00 |
| 353. |
Class I BOP system — fail to have a tubing stripper |
4.6.8.1 (c) |
$400.00 |
| 354. |
Class II &III BOP lines — fail to ensure lines are of steel or flexible hose |
4.6.8.2 (a) |
$400.00 |
| 355. |
Class II &III BOP lines — fail to have lines that are valved and of proper pressure |
4.6.8.2 (b) |
$400.00 |
| 356. |
Class II & III BOP lines — fail to have lines that are connected to rig pump and tank |
4.6.8.2 (c) |
$400.00 |
| 357. |
Class II & III BOP lines — fail to have lines that are properly fitted and connected |
4.6.8.2 (d) |
$400.00 |
| 358. |
Class II & III BOP lines — fail to have lines of proper diameter |
4.6.8.2 (e) |
$400.00 |
| 359. |
Class II & III BOP lines — fail to ensure lines are securely tied down |
4.6.8.2 (f) |
$400.00 |
| 360. |
Class II & III BOP manifold — fail to ensure valves and steel lines with proper pressure |
4.6.9 (a) |
$400.00 |
| 361. |
Class II & III BOP manifold — fail to have check valve |
4.6.9 (b) |
$400.00 |
| 362. |
Class II & III BOP manifold — fail to have pressure relief valve |
4.6.9 (c) |
$400.00 |
| 363. |
Class II & III BOP manifold — fail to install or have available accurate gauge |
4.6.9 (d) |
$400.00 |
| 364. |
Fail to provide accurate pressure gauge during well shut-in |
4.6.10 |
$400.00 |
| 365. |
Fail to maintain on a service rig a safety valve in the open position |
4.6.11 |
$400.00 |
| 366. |
Fail to conduct a pressure test on each preventer prior to commencing operations |
4.6.12 |
$400.00 |
| 367. |
Fail to conduct pressure test on preventers with pipe in the hole |
4.6.13 |
$500.00 |
| 368. |
Fail to ensure BOP equipment is mechanically tested daily |
4.6.14 |
$500.00 |
| 369. |
Fail to record tests in log book |
4.6.15 |
$400.00 |
| 370. |
Fail to ensure properly certified driller at site |
4.6.17 (a) |
$700.00 |
| 371. |
Fail to ensure rig crew is trained in operation of BOP equipment |
4.6.17 (b) |
$700.00 |
| 372. |
Fail to ensure that BOP drills are performed every 7 days |
4.6.17 (c) |
$500.00 |
| 373. |
Fail to ensure BOP drills are recorded in log book |
4.6.17 (d) |
$400.00 |
| 374. |
Fail to provide sufficient heat in cold weather to ensure BOP system effective |
4.6.18 |
$400.00 |
| 375. |
Fail to properly space equipment at well site |
4.7 |
$400.00 |
| 376. |
Fail to maintain orderly work site |
5.1 (a) |
$750.00 |
| 377. |
Fail to safely store all chemicals and fuel |
5.1 (b) |
$750.00 |
| 378. |
Fail to properly remove and dispose of waste and unused equipment |
5.1 (c) |
$750.00 |
| 379. |
Fail to properly dispose of oil field fluid produced from a well |
5.1.1 (a) |
$750.00 |
| 380. |
Fail to properly handle, store or dispose of any products or waste |
5.1.1 (b) |
$750.00 |
| 381. |
Fail to immediately remove product or waste that create a hazard |
5.1.1 (c) |
$750.00 |
| 382. |
Fail to dispose of and keep stimulation fluids separate from oil field fluids |
5.1.1 (d) |
$550.00 |
| 383. |
Fail to identify well with prominent sign |
5.2 |
$450.00 |
| 384. |
Fail to mark battery or production site with name of operator |
5.3 (a) |
$450.00 |
| 385. |
Fail to show operator’s name and emergency phone number at site |
5.3 (b) |
$450.00 |
| 386. |
Fail to prevent waste of oil or gas |
5.4 (a) |
$750.00 |
| 387. |
Fail to flare gas |
5.4 (b) |
$450.00 |
| 388. |
Fail to meet setback requirements |
5.5 |
$500.00 |
| 389. |
Locate flares less than 75 metres from buildings |
5.5.1 (a) |
$500.00 |
| 390. |
Locate flares less than 50 metres from pipeline, electrical lines,railway or aircraft runway |
5.5.1 (b) |
$500.00 |
| 391. |
Locate flares less than 30 metres from wellhead, tanks and buildings |
5.5.1 (c) |
$500.00 |
| 392. |
Locate flares less than 15 metres from compressors, coolers, vessels and substations |
5.5.1 (d) |
$500.00 |
| 393. |
Locate oil and brine tanks less than 75 metres from buildings |
5.5.2 (a) |
$500.00 |
| 394. |
Locate oil and brine tanks less than 30 metres from pipelines, electrical lines, pits, office or switch gear |
5.5.2 (b) |
$500.00 |
| 395. |
Locate oil and brine tanks less than 20 metres from wellhead, railway or road allowance |
5.5.2 (c) |
$500.00 |
| 396. |
Locate oil and brine tanks less than 15 metres from compressors, buildings, coolers, heaters or vessels |
5.5.2 (d) |
$500.00 |
| 397. |
Locate oil and brine tanks less than 1 metre from other oil and brine tanks |
5.5.2 (e) |
$500.00 |
| 398. |
Locate process vessel less than 60 metres from buildings |
5.5.3 (a) |
$500.00 |
| 399. |
Locate process vessel less than 20 metres from railway or road allowance |
5.5.3 (b) |
$500.00 |
| 400. |
Locate process vessel less than 15 metres from tanks, pits, wellhead or office |
5.5.3 (c) |
$500.00 |
| 401. |
Locate process vessel less than 10 metres from other vessels |
5.5.3 (d) |
$500.00 |
| 402. |
Locate process vessel 7 metres from tanks where vessel is unfired |
5.5.3 (e) |
$500.00 |
| 403. |
Fail to properly equip diesel engines |
5.5.4 |
$500.00 |
| 404. |
Fail to ensure internal combustion engine is 15 metres from well when obtaining air |
5.5.4.1 |
$500.00 |
| 405. |
Engine exhaust pipe — fail to prevent emergence of flame |
5.5.4.2 (a) |
$500.00 |
| 406. |
Engine exhaust pipe — fail to ensure pipe end is 2 metres from well |
5.5.4.2 (b) |
$500.00 |
| 406.1 |
Fail to store oil or oil field fluids in proper container |
5.6 (a) |
$700.00 |
| 406.2 |
Store oil and oil field fluids in earthen pit, pond or underground tank |
5.6 (b) |
N.S.F. |
| 407. |
Fluid storage tanks — fail to surround with dike or firewall of proper capacity |
5.6.1 (a) |
$700.00 |
| 408. |
Fluid storage tanks — insufficient permeability |
5.6.1 (b) |
$700.00 |
| 409. |
Fluid storage tanks — fail to maintain dike or firewall in good condition |
5.6.1 (c) |
$500.00 |
| 410. |
Fail to use proper above ground storage tank to store oil and brine |
5.6.2 |
$700.00 |
| 411. |
Fail to electrically ground above ground tank |
5.6.4 (a) |
$500.00 |
| 412. |
Fail to electrically ground trucks when loading/unloading |
5.6.4 (b) |
$500.00 |
| 413. |
Fail to comply with API RP651 for cathodically protected above ground tanks |
5.6.5 |
$500.00 |
| 414. |
Storage tank nameplate — fail to state construction standard |
5.6.6 (a) |
$350.00 |
| 415. |
Storage tank nameplate — fail to state the year built |
5.6.6 (b) |
$350.00 |
| 416. |
Storage tank nameplate — fail to state capacity |
5.6.6 (c) |
$350.00 |
| 417. |
Storage tank nameplate — fail to state fabricator |
5.6.6 (d) |
$350.00 |
| 418. |
Storage tank nameplate — fail to state diameter and height |
5.6.6 (e) |
$350.00 |
| 419. |
Piping systems — fail to use proper pipeline |
5.7 |
$700.00 |
| 420. |
Piping systems — fail to use proper material for pipeline fabrication and installation |
5.7.1 |
$700.00 |
| 421. |
Piping systems — fail to provide a certified Examiner for pipeline construction |
5.7.2 |
$700.00 |
| 422. |
Piping systems — fail to have proper pipeline burial depth |
5.7.3 |
$700.00 |
| 423. |
Pressure vessel — fail to properly install, repair, construct or inspect |
5.8 |
$750.00 |
| 424. |
Well flare stacks — fail to have proper height and diameter |
5.9 (a) |
$450.00 |
| 425. |
Well flare stacks — fail to have proper height and diameter |
5.9 (b) |
$450.00 |
| 426. |
Well flare stacks — fail to properly install, operate and design |
5.9 (c) |
$450.00 |
| 427. |
Gas compressors — fail to properly design, construct, operate and maintain |
5.10.1 (a) |
$750.00 |
| 428. |
Gas compressors — fail to ensure shutdown controls operate properly |
5.10.1 (b) |
$450.00 |
| 429. |
Gas compressors — fail to ensure shut down controls are triggered on high and low pressure |
5.10.1 (c) |
$450.00 |
| 430. |
Fail to ensure electrical materials conform to Electrical Code |
5.11 (a) |
$350.00 |
| 431. |
Fail to ensure electrical materials conform to CSA |
5.11 (b) |
$350.00 |
| 432. |
Fail to ensure electrical materials conform to API Standards |
5.11 (c) |
$350.00 |
| 433. |
Fail to ensure electrical materials conform to the Shipping Act (Canada) |
5.11 (d) |
$350.00 |
| 434. |
Fail to ensure electrical equipment is installed by qualified electrician |
5.11.1 |
$350.00 |
| 435. |
Fail to ensure pressure control, limiting and relieving equipment conform to CSA code |
5.12 |
$350.00 |
| 436. |
Fail to ensure that fires are safeguarded to avoid a hazard |
5.13 (a) |
$500.00 |
| 437. |
Fail to store explosives 150 metres from work |
5.13 (b) |
$500.00 |
| 438. |
Fail to provide for an Examiner to check works weekly for leaks or spills |
5.14 (a) |
$450.00 |
| 439. |
Fail to provide for an Examiner to check works weekly for damage |
5.14 (b) |
$450.00 |
| 440. |
Fail to provide for an Examiner to check works weekly for unsafe conditions |
5.14 (c) |
$450.00 |
| 441. |
Fail to provide for an Examiner to certify annually that works comply with Provincial Standards |
5.14.1 |
$450.00 |
| 442. |
Suspended wells — fail to isolate all zones from one another |
5.15 (a) |
$600.00 |
| 443. |
Suspended wells — fail to ensure all fresh water zones are isolated by cemented casing |
5.15 (b) |
$600.00 |
| 444. |
Porous and permeable fluid bearing zones — fail to isolate zones with bridge plug and cement |
5.15.1 (a) |
$550.00 |
| 445. |
Porous and permeable fluid bearing zones — fail to isolate zone with a bridge capped with stone and cement |
5.15.1 (b) |
$550.00 |
| 446. |
Porous and permeable fluid bearing zones — fail to isolate zones by alternative technique |
5.15.1 (c) |
$550.00 |
| 447. |
Porous and permeable fluid bearing zone — fail to ensure cementing procedures and design complies with Provincial Standards |
5.15.1 (d) |
$550.00 |
| 448. |
Suspended well onshore — fail to have two bull-plugged valves |
5.15.2 (a) |
$400.00 |
| 449. |
Suspended well onshore — fail to install two valve and bull-plugged side outlets |
5.15.2 (b) |
$400.00 |
| 450. |
Suspended well onshore — fail to isolate the intermediate casing annulus before suspending well |
5.15.2 (c) |
$400.00 |
| 451. |
Suspended well onshore — fail to provide access to a two-valved bull plug at annulus |
5.15.2 (d) |
$400.00 |
| 452. |
Suspended well onshore — fail to protect wellhead with steel posts or fencing |
5.15.2 (e) |
$400.00 |
| 453. |
Suspended well onshore — fail to remove valve handles or install lock and chain |
5.15.3 (a) |
$400.00 |
| 454. |
Suspended well onshore — fail to enclose well site with building or chain-link fence |
5.15.3 (b) |
$400.00 |
| 455. |
Suspended well onshore — fail to inspect wellhead and valves for leaks |
5.15.4 |
$400.00 |
| 456. |
Suspended well onshore — fail to lubricate and service wellhead valves annually |
5.15.5 |
$400.00 |
| 457. |
Suspended well onshore — fail to provide for an Examiner to certify well suspended properly |
5.15.6 (a) |
$550.00 |
| 458. |
Suspended well onshore — fail to annually examine all valve outlets for safety and integrity |
5.15.6 (b) |
$550.00 |
| 459. |
Site rehabilitation — fail to rehabilitate within one year of end of operations |
5.16 |
$700.00 |
| 460. |
Site rehabilitation — fail to dispose of all liquid and solid waste |
5.16 (a) |
$700.00 |
| 461. |
Site rehabilitation — fail to clean area of all debris |
5.16 (b) |
$700.00 |
| 462. |
Site rehabilitation — fail to drain and fill excavations |
5.16 (c) |
$700.00 |
| 463. |
Site rehabilitation — fail to remove surface works, concrete, machinery and materials |
5.16 (d) |
$700.00 |
| 464. |
Site rehabilitation — fail to level and restore grade |
5.16 (e) |
$700.00 |
| 465. |
Site rehabilitation — fail to provide Examiner to certify rehabilitation complies with Provincial Standards |
5.16 (f) |
$750.00 |
| 466. |
Water covered area — fail to ensure wellhead is properly located and encased |
5.17 (a) |
$750.00 |
| 467. |
Water covered area — fail to ensure wellhead is properly located in fishing area |
5.17.1 |
$750.00 |
| 468. |
Water covered area — fail to remove structure within 30 days of end of drilling or plugging |
5.17.2 |
$750.00 |
| 469. |
Water covered area — Use a platform not approved by the Ministry |
5.17.3 |
N.S.F. |
| 470. |
Well in water covered area — fail to mark each well and pipeline junction |
5.17.4 (a) |
$550.00 |
| 471. |
Well in water covered area — fail to identify operator and junction designation |
5.17.4 (b) |
$550.00 |
| 472. |
Well in water covered area — fail to maintain markers |
5.17.4 (c) |
$350.00 |
| 472.1 |
Offshore pipeline gathering system not designed, constructed or maintained in accordance with CSA Z662-99 |
5.17.5 |
N.S.F. |
| 473. |
Fail to install metering equipment to measure tubing and casing pressure |
6.1 (a) |
$450.00 |
| 474. |
Fail to install metering equipment to measure flow rate |
6.1 (b) |
$450.00 |
| 475. |
Fail to install metering equipment to permit oil, gas or water sampling |
6.1 (c) |
$450.00 |
| 476. |
Fail to keep records of quantities of oil, gas and water produced |
6.2 (a) |
$400.00 |
| 477. |
Fail to keep records of average separator pressure |
6.2 (b) |
$400.00 |
| 478. |
Fail to keep records of product disposition |
6.2 (c) |
$400.00 |
| 479. |
Fail to keep records of purchaser and amount realized |
6.2 (d) |
$400.00 |
| 480. |
Fail to prevent waste of hydrocarbon resources |
6.3 (a) |
$700.00 |
| 481. |
Fail to prevent the waste of reservoir energy |
6.3 (b) |
$700.00 |
| 482. |
Fail to maximize ultimate recovery of oil and gas |
6.3 (c) |
$700.00 |
| 483. |
Fail to minimize flaring or venting of gas |
6.3 (d) |
$700.00 |
| 484. |
Fail to obtain information to optimize production and evaluate conservation |
6.4 |
$400.00 |
| 485. |
Fail to maintain monthly records of production volumes, reservoir pressure and fluids injected |
6.4.1 |
$400.00 |
| 486. |
Fail to properly meter for fluid and gas measurements |
6.5 |
$500.00 |
| 487. |
Fail to ensure meter accuracy for fluid and gas measurements |
6.6 (a) |
$500.00 |
| 488. |
Fail to ensure meter re-calibration |
6.6 (b) |
$500.00 |
| 489. |
Fail to report bottom hole pressure to Ministry on Form 7 |
6.7 |
$400.00 |
| 490. |
Fail to properly determine bottom-hole pressure |
6.8 |
$400.00 |
| 491. |
Fail to take a gas or oil sample for each new oil pool |
6.9 |
$400.00 |
| 492. |
Initial production testing period report — fail to include daily production volumes on report |
6.10 (a) |
$400.00 |
| 493. |
Initial production testing period report — fail to include estimate of well’s potential |
6.10 (b) |
$400.00 |
| 494. |
Initial production testing period report — fail to include plans for gas conservation |
6.10 (c) |
$400.00 |
| 495. |
Initial production testing period report — fail to include evaluation, estimate and pool boundary |
6.10 (d) |
$400.00 |
| 496. |
Initial production testing period report — fail to include bottom hole pressure |
6.10 (e) |
$400.00 |
| 497. |
Fail to flare gas |
6.11 |
$550.00 |
| 498. |
Permit flaring in excess of permitted monthly volumes |
6.11.1 |
$550.00 |
| 498.1 |
Fail to produce well evenly throughout the month |
6.11.3 |
$550.00 |
| 499. |
Fail to contain flaring within permitted monthly volumes — same pool, 2 or more wells |
6.11.4 |
$550.00 |
| 500. |
Fail to take an annual shut-in pressure measurement |
6.12 (a) |
$400.00 |
| 500.1 |
Fail to report measurements |
6.12 (b) |
$400.00 |
| 501. |
Fail to report observed field data re deliverability of well to Ministry on Form 7 |
6.12 (c) |
$400.00 |
| 502. |
Fail to take annual shut-in pressure with dead-weight gauge |
6.12.1 (a) |
$400.00 |
| 503. |
Fail to take annual shut-in pressure within proper time |
6.12.1 (b) |
$400.00 |
| 504. |
Fail to report annual shut-in pressure on Form 8 |
6.12.1 (c) |
$400.00 |
| 505. |
Design — fail to permanently protect water formations from contamination |
7 (a) |
$750.00 |
| 506. |
Design — fail to protect existing formations from injected fluid |
7 (b) |
$750.00 |
| 507. |
Design — fail to prevent migration of fluids between formations |
7 (c) |
$750.00 |
| 508. |
Operation — fail to ensure that disposal fluids are compatible with disposal formation |
7 (d) |
$750.00 |
| 509. |
Operation — fail to ensure that disposal fluids are retained within formation |
7 (e) |
$750.00 |
| 510. |
Construction — fail to notify in writing landowners and operators within 750 metres |
7.1 (a) |
$450.00 |
| 511. |
Construction — fail to notify in writing the local municipality |
7.1 (b) |
$450.00 |
| 512. |
Construction — fail to notify Ministry in writing |
7.1 (c) |
$450.00 |
| 513. |
Design — fail to provide for injection of oil field fluid through tubing |
7.2 (a) |
$450.00 |
| 514. |
Design — fail to provide isolation of annular space between tubing and casing from injection zone |
7.2 (b) |
$450.00 |
| 515. |
Design — fail to include corrosion inhibitor |
7.2 (c) |
$450.00 |
| 516. |
Design — fail to provide for isolation of fresh water zones |
7.2 (d) |
$450.00 |
| 517. |
Design — fail to provide for cementing the surface casing |
7.2 (e) |
$450.00 |
| 518. |
Design — fail to provide for proper wellhead components |
7.2 (f) |
$450.00 |
| 519. |
Water sampling — fail to collect samples for each penetrated aquifer and record depth |
7.3 (a) |
$400.00 |
| 520. |
Water sampling — fail to provide a copy of the chemical analysis of water in penetrated aquifer to the Ministry |
7.3 (b) |
$400.00 |
| 521. |
Convert existing well 20 years or older to a disposal well |
7.4.1 |
$750.00 |
| 522. |
Fail to submit completed disposal report |
7.5 |
$200.00 |
| 523. |
Disposal operations — inject oil field fluid from another source |
7.6 (a) |
$200.00 |
| 524. |
Disposal operations — inject liquid industrial waste |
7.6 (b) |
$200.00 |
| 525. |
Disposal operations — inject oil field fluid between outermost casing and well bore or annular space between strings of casing |
7.6 (c) |
$200.00 |
| 545. |
Fail to inject oil field fluids by gravity feed |
7.7 (a) |
$550.00 |
| 546. |
Fail to inject oil field fluids into formations as deep as practical |
7.7 (b) |
$550.00 |
| 547. |
Pre-commissioning — fail to identify wells within 750 metres |
7.8 (a) |
$500.00 |
| 548. |
Pre-commissioning — fail to confirm integrity of injection casing by pressure tests or cement logs |
7.8 (b) |
$500.00 |
| 548.1 |
Pre-commissioning — fail to run a cement bond log to verify cement integrity |
7.8 (c) |
$750.00 |
| 549. |
Pre-commissioning — fail to conduct injectivity test |
7.8 (d) |
$400.00 |
| 550. |
Pre-commissioning — fail to submit a disposal report |
7.8 (e) |
$400.00 |
| 551. |
Pre-commissioning — fail to submit an operating procedure |
7.8 (f) |
$400.00 |
| 552. |
Well within 750 metres of water well — fail to report depth of water well |
7.8.1 (a) |
$400.00 |
| 553. |
Well within 750 metres of water well — fail to report the age of water well |
7.8.1 (b) |
$400.00 |
| 554. |
Well within 750 metres of water well — fail to report volume of water taken from water well |
7.8.1 (c) |
$400.00 |
| 555. |
Well within 750 metres of water well — fail to report static level of water in water well |
7.8.1 (d) |
$400.00 |
| 556. |
Injection test — fail to submit initial test |
7.9 |
$400.00 |
| 557. |
Injection test — fail to include the depths of the injection intervals |
7.9.1 (a) |
$400.00 |
| 558. |
Injection test — fail to include the rates of injection |
7.9.1 (b) |
$400.00 |
| 559. |
Injection test — fail to include the injection pressures |
7.9.1 (c) |
$400.00 |
| 560. |
Injection test — fail to include the volume and source of fluids |
7.9.1 (d) |
$400.00 |
| 561. |
Injection test — fail to ensure proper pressure during initial test |
7.9.2 |
$400.00 |
| 562. |
Injection test — initial test more than 30 days in duration |
7.9.3 (a) |
$400.00 |
| 563. |
Injection test — initial test exceeds 500 m³ of injected fluid |
7.9.3 (b) |
$400.00 |
| 563.1 |
Commence disposal operations without written approval from the Ministry |
7.10 |
N.S.F. |
| 564. |
Fail to measure the volume of injected fluid and pressure |
7.10.1 |
$400.00 |
| 565. |
Fail to verify presence of corrosion inhibiting fluid by certified Examiner |
7.10.2 |
$400.00 |
| 566. |
Fail to ensure subsurface pressure does not exceed 75 per cent of fracture pressure |
7.10.3 |
$400.00 |
| 567. |
Fail to keep plans and maps of disposal well |
7.11 |
$400.00 |
| 568. |
Fail to have a spill contingency plan |
7.12 |
$400.00 |
| 569. |
Fail to conduct a pressure test of annular space every 5 years |
7.13 |
$400.00 |
| 570. |
Fail to stop injection of fluid where loss of fluid or increase in pressure |
7.14 |
$400.00 |
| 571. |
Fail to maintain complete records for each disposal well |
7.15 |
$400.00 |
| 583. |
Fail to provide for an Examiner to examine facilities semi-annually |
7.16 |
$450.00 |
| 584. |
Well servicing — fail to install and maintain BOP |
8.1 |
$700.00 |
| 585. |
Well servicing — fail to ensure proper rating on lubricator system |
8.1.1 |
$400.00 |
| 586. |
Well servicing — fail to ensure proper spacing of equipment |
8.2 |
$400.00 |
| 587. |
Well servicing — fail to install pressure gauge to determine well annulus pressure |
8.3 |
$400.00 |
| 588. |
Well servicing — fail to maintain stabbing valve in open position |
8.5 |
$400.00 |
| 589. |
Well servicing — fail to use a stub lubricator system |
8.6 |
$400.00 |
| 590. |
Well servicing — fail to properly ground electrical system |
8.7 |
$400.00 |
| 591. |
Well servicing — fail to keep a record of all servicing on well |
8.10 |
$400.00 |
| 591.1 |
Fail to design and construct salt solution mine as required |
9.1 |
N.S.F. |
| 592. |
Fail to ensure mining operations are 150 metres from operator’s property boundary |
9.5 (b) |
$700.00 |
| 593. |
Fail to ensure salt extraction is 50 metres from operator’s property boundary |
9.5 (c) |
$700.00 |
| 594. |
Fail to ensure caverns and galleries have tight hydraulic control |
9.5.1 |
$700.00 |
| 595. |
Fail to employ a blanketing material for roof control |
9.6 |
$700.00 |
| 596. |
Drilling — fail to cement to surface all casings |
9.7 (a) |
$700.00 |
| 597. |
Drilling — fail to set production casing 3 metres into salt formation |
9.7 (b) |
$700.00 |
| 598. |
Drilling — fail to include a cement bond log and casing evaluation log |
9.7 (c) (i) |
$700.00 |
| 599. |
Drilling — fail to conduct pressure test on production casing and seat |
9.7 (c) (ii) |
$700.00 |
| 600. |
Drilling — fail to conduct pressure test of the formation below production casing seat |
9.7 (c) (iii) |
$700.00 |
| 601. |
Drilling — hanging tubing string does not comply with API standard |
9.7 (d) |
$700.00 |
| 601.1 |
Fail to carry out solution mining operations in accordance with written mining plan |
9.8 |
N.S.F. |
| 602. |
Operation and monitoring — no operating and maintenance procedures |
9.8.1 (a) (i) |
$700.00 |
| 603. |
Operation and monitoring — no emergency response procedures |
9.8.1 (a) (ii) |
$700.00 |
| 604. |
Operation and monitoring — no procedures re performance of maintenance functions |
9.8.1 (a) (iii) |
$700.00 |
| 605. |
Operation and monitoring — fail to comply with operating and maintenance procedures |
9.8.1 (b) |
$700.00 |
| 606. |
Operation and monitoring — fail to keep records necessary to administer operating and maintenance procedures |
9.8.1 (c) |
$700.00 |
| 607. |
Operation and monitoring — fail to ensure staff are trained |
9.8.1 (d) |
$700.00 |
| 608. |
Operation and monitoring — fail to update operating and maintenance procedures as required |
9.8.1 (e) |
$700.00 |
| 609. |
Operating and monitoring — fail to limit the maximum injection and withdrawal rates |
9.8.1 (f) |
$700.00 |
| 610. |
Operating and monitoring — fail to maintain documents for activities on wells and pipelines |
9.8.1 (g) (i) |
$400.00 |
| 611. |
Operating and monitoring — fail to maintain documents for downhole activities and copies of all logs |
9.8.1 (g) (ii) |
$400.00 |
| 612. |
Operating and monitoring — fail to keep daily records of water injected and brine recovered |
9.8.1 (h) (i) |
$400.00 |
| 613. |
Operating and monitoring — fail to keep daily records of volume and pressure of blanketing material |
9.8.1 (h) (ii) |
$400.00 |
| 613.1 |
Fail to conduct mechanical integrity testing as required |
9.8.2 (a) |
N.S.F. |
| 614. |
Fail to provide for an Examiner to certify the mechanical integrity of each well |
9.8.2 (b) |
$750.00 |
| 615. |
Fail to monitor hydraulic closure and provide Examiner certification annually |
9.8.3 |
$750.00 |
| 615.1 |
Fail to conduct sonar survey |
9.8.4 (a) |
N.S.F. |
| 616. |
Fail to plot the results of the sonar survey |
9.8.4 (b) |
$500.00 |
| 616.1 |
Fail to use sonar survey to ensure solution mining is in accordance with mining plan |
9.8.4 (c) |
N.S.F. |
| 617. |
Fail to conduct subsidence monitoring annually using a qualified surveyor |
9.8.5 (a) |
$550.00 |
| 618. |
Fail to properly record the subsidence data and submit to Ministry |
9.8.5 (b) |
$550.00 |
| 619. |
Fail to comply with well servicing requirements |
9.8.6 |
$750.00 |
| 620. |
Abandonment — fail to include a sonar survey on the cavern |
9.9 (a) |
$750.00 |
| 621. |
Abandonment — fail to include a mechanical test on the casing |
9.9 (b) |
$750.00 |
| 621.1 |
Fail to plug solution mining well |
9.9 (c) |
N.S.F. |
| 621.2 |
Fail to comply with CSA Standard Z341-98 Storage of Hydrocarbons in Underground Formations |
10 |
N.S.F. |
| 622. |
Hydrocarbon storage — fail to have Examiner validate mechanical integrity test |
10.1 |
$750.00 |
| 623. |
Hydrocarbon storage — fail to conduct annual examination of surface works certified by Examiner |
10.2 |
$750.00 |
| 624. |
Fail to notify the Ministry of well overhauls |
10.3 (a) (i) |
$700.00 |
| 625. |
Fail to notify the Ministry of a change of service in a cavern |
10.3 (a) (ii) |
$700.00 |
| 626. |
Fail to notify the Ministry of damage or leak at well head or casing |
10.3 (a) (iii) |
$700.00 |
| 627. |
Fail to notify the Ministry of emergency |
10.3 (b) |
$700.00 |
| 628. |
Fail to ensure protection of oil or gas producing horizons |
11 (a) |
$700.00 |
| 629. |
Fail to prevent the migration of oil, gas or water |
11 (b) |
$700.00 |
| 630. |
Fail to seal off and isolate all porous formations |
11 (c) |
$700.00 |
| 631. |
Fail to ensure plugging does not constitute a hazard to surface users |
11 (d) |
$700.00 |
| 632. |
Fail to plug hydrocarbon storage wells in accordance with CSA Z341-98 |
11.1 (a) |
$700.00 |
| 633. |
Fail to plug in accordance with section 9.9 of the Standards |
11.1 (b) |
$700.00 |
| 634. |
Fail to properly remove casing, tubing and material from well |
11.2. |
$500.00 |
| 635. |
Fail to use neat cement |
11.3 (a) (i) |
$500.00 |
| 636. |
Fail to mix cement in accordance with API Specifications |
11.3 (a) (ii) |
$500.00 |
| 637. |
Fail to make cement plug in the form of a water base slurry |
11.3 (a) (iii) |
$500.00 |
| 638. |
Fail to make cement plug sulphate resistant |
11.3 (a) (iv) |
$500.00 |
| 639. |
Fail to make bridges of wood, stone, gravel or lead |
11.3 (b) |
$500.00 |
| 640. |
Fail to deposit cement plug by displacement or dump bailer |
11.4 |
$500.00 |
| 641. |
Fail to ensure pumped cement plugs have sufficient slurry volume |
11.5 (a) |
$500.00 |
| 642. |
Fail to ensure dump-bailed plugs have sufficient volume |
11.5 (b) |
$500.00 |
| 643. |
Fail to locate plug at top of each zone or salt cavern and certify location |
11.6 (a) |
$500.00 |
| 644. |
Fail to locate the top most plug set in the well and certify location |
11.6 (b) |
$500.00 |
| 645. |
Fail to fill area between plugs with water or drilling mud |
11.7 |
$500.00 |
| 646. |
Fail to set cement plugs above and below each oil, gas and fluid bearing zone |
11.8 (a) |
$500.00 |
| 647. |
Fail to set cement plugs at top of formations |
11.8 (b) |
$500.00 |
| 648. |
Fail to extend plugs 8 metres in the well |
11.9 |
$500.00 |
| 649. |
Fail to properly recover casing when surface casing is left in hole |
11.10 (a) |
$500.00 |
| 650. |
Fail to properly recover casing when surface casing is removed |
11.10 (b) |
$500.00 |
| 651. |
Fail to place a cement plug 15 metres below zone and 15 metres above top of zone |
11.10 (c) |
$700.00 |
| 652. |
Fail to set plug across shoe of surface casing |
11.11 (a) |
$700.00 |
| 653. |
Fail to place plug inside the surface casing |
11.11 (b) |
$700.00 |
| 654. |
Fail to place plug inside casing below the base where intermediate casing cemented |
11.11 (c) |
$700.00 |
| 655. |
Fail to place plug across the shoe where intermediate casing to be left |
11.11 (d) |
$700.00 |
| 656. |
Fail to recover casing to allow placement of plugs where intermediate casing not cemented |
11.11 (e) |
$700.00 |
| 657. |
Fail to place plug inside casing below the base where production casing cemented |
11.11 (f) |
$700.00 |
| 658. |
Fail to recover casing to allow placement of plug where production casing not cemented |
11.11 (g) |
$700.00 |
| 659. |
Fail to set 8 metre plug at top of productive zone |
11.11 (h) |
$700.00 |
| 660. |
Rehabilitation — onshore well — fail to dispose of all waste |
11.13 (a) |
$700.00 |
| 661. |
Rehabilitation — onshore well — fail to clear the area of all debris |
11.13 (b) |
$700.00 |
| 662. |
Rehabilitation — onshore well — fail to drain and fill excavations |
11.13 (c) |
$700.00 |
| 663. |
Rehabilitation — onshore well — fail to remove all surface works |
11.13 (d) |
$700.00 |
| 664. |
Rehabilitation — onshore well — fail to level and restore original grade of the site |
11.13 (e) |
$700.00 |
| 665. |
Rehabilitation — water covered area — fail to cut off any casing in water covered site |
11.13.1 |
$750.00 |
| 666. |
Rehabilitation — fail to record and submit Form 10 for every plugged well |
11.14 |
$400.00 |
| 667. |
Fail to calculate using proper rates |
12 (a) |
$450.00 |
| 668. |
Fail to make fee payment |
12 (b) |
$450.00 |
| 669. |
Fail to submit Form 7 with fee payment |
12 (c) |
$450.00 |
| 670. |
Drilling activity notice — fail to notify Ministry 48 hours prior to drilling |
13.2 (a) |
$400.00 |
| 671. |
Drilling activity notice — fail to notify Ministry of drilling suspension date within 48 hours |
13.2 (b) (i) |
$400.00 |
| 672. |
Drilling activity notice — fail to notify Ministry of well depth within 48 hours |
13.2 (b) (ii) |
$400.00 |
| 673. |
Drilling activity notice — fail to notify Ministry of well condition within 48 hours |
13.2 (b) (iii) |
$400.00 |
| 674. |
Drilling activity notice — fail to notify Ministry of total depth and status of well within 48 hours of TD date |
13.2 (c) |
$400.00 |
| 675. |
Drilling activity notice — fail to notify Ministry of completion date and well status within 48 hours |
13.2 (d) |
$400.00 |
| 676. |
Drilling activity notice — fail to notify the Ministry 48 hours prior to plugging a well |
13.2 (e) |
$400.00 |
| 676.1 |
Fail to report emergency notification in writing |
13.3 |
N.S.F. |
| 677. |
Fail to complete a Drilling and Completion Report in Form 7 within 60 days of end of operation |
13.4 |
$400.00 |
| 678. |
Fail to deliver drilling samples within 30 days |
13.5 |
$400.00 |
| 679. |
Fail to properly pack and label drill cores |
13.6 (a) |
$400.00 |
| 680. |
Fail to submit core or other analysis to Ministry within 30 days of completion |
13.6.1 |
$400.00 |
| 681. |
Fail to ensure no core is destroyed |
13.7 (a) |
$400.00 |
| 682. |
Fail to ensure cores are delivered to library within 1 year of TD date |
13.7 (b) |
$400.00 |
| 683. |
Fail to supply logs or surveys to the Ministry within 30 days |
13.8 |
$400.00 |
| 684. |
Fail to complete Form 7 within 30 days of any well activities other than drilling or deepening |
13.9 |
$400.00 |
| 685. |
Fail to submit connate water determinations within 30 days |
13.10 (a) |
$400.00 |
| 686. |
Fail to submit copies of drill stem and production test within 30 days |
13.10 (b) |
$400.00 |
| 687. |
Fail to submit static hole pressure measurements within 30 days |
13.10 (c) |
$400.00 |
| 688. |
Fail to submit pressure measurements and back pressure tests within 30 days |
13.10 (d) |
$400.00 |
| 689. |
Fail to submit gas ratios within 30 days |
13.10 (e) (i) |
$400.00 |
| 690. |
Fail to submit liquid phase volumes within 30 days |
13.10 (e) (ii) |
$400.00 |
| 691. |
Fail to submit formation volume factors within 30 days |
13.10 (e) (iii) |
$400.00 |
| 692. |
Fail to submit tank oil gravities within 30 days |
13.10 (e) (iv) |
$400.00 |
| 693. |
Fail to submit separator and stock tank gas-oil ratios within 30 days |
13.10 (e) (v) |
$400.00 |
| 694. |
Fail to submit bubble point pressure of reservoir fluid within 30 days |
13.10 (e) (vi) |
$400.00 |
| 695. |
Fail to submit compressibility of saturated reservoir oil within 30 days |
13.10 (e) (vii) |
$400.00 |
| 696. |
Fail to submit viscosity of reservoir oil within 30 days |
13.10 (e) (viii) |
$400.00 |
| 697. |
Fail to submit fractional analysis of casing head gas and reservoir fluid within 30 days |
13.10 (e) (ix) |
$400.00 |
| 698. |
Fail to submit Annual Production Report of Monthly Well or Field/Pool Production by February 15 |
13.11 |
$400.00 |
| 699. |
Fail to submit an Annual Report on Monthly Injection by February 15 |
13.12 |
$400.00 |
| 700. |
Disposal well — fail to submit records of pressure measurements and tests within 30 days |
13.13 (a) (i) |
$400.00 |
| 701. |
Disposal well — fail to submit copies of chemical analysis from water wells within 30 days |
13.13 (a) (ii) |
$400.00 |
| 702. |
Disposal well — fail to submit the mechanical integrity test within 30 days |
13.13 (a) (iii) |
$400.00 |
| 703. |
Disposal well — fail to submit an Annual Subsurface Fluid Disposal Report by February 15 |
13.13 (b) |
$400.00 |
| 704. |
Disposal well — fail to submit a Plugging of a Well Report within 30 days |
13.14 |
$400.00 |
| 705. |
Disposal well — fail to submit an Annual Report of Geophysical/Agrochemical Activity by February 15 |
13.15 |
$400.00 |
| 706. |
Annual well status report — fail to show all the wells |
13.16 (a) |
$400.00 |
| 707. |
Annual well status report — fail to show the status of each well |
13.16 (b) |
$400.00 |
| 708. |
Annual well status report — fail to show calculation of well licence fee |
13.16 (c) |
$400.00 |
| 709. |
Annual well status report — not accompanied by licence fee |
13.16 (d) |
$400.00 |
| 710. |
Third party gas report — fail to submit by February 15 |
13.16 |
$400.00 |
| 711. |
Fail to submit completed third party gas report |
13.17 |
$700.00 |
| 712. |
Fail to submit completed third party oil report |
13.18 |
$700.00 |
| 722. |
Fail to submit the Initial Production Test Period Report within 10 days |
13.19 |
$400.00 |
| 723. |
Fail to report voluntarily unitized unit area and required information |
13.20 |
$400.00 |
| 724. |
Fail to report voluntarily amended unit area required information |
13.21 |
$400.00 |
| 736. |
Fail to submit an Annual Report of Solution Mined Salt Production by February 15 |
13.22 |
$400.00 |
| 737. |
Salt solution mining — fail to submit results of all tests within 30 days |
13.23 |
$400.00 |
| 737.1 |
Fail to immediately contact Ministry in case of spill or subsidence occurrence |
13.24 |
N.S.F. |
| 738. |
Underground storage tanks — fail to construct a dike surrounding the tank |
14.2 (a) |
$700.00 |
| 739. |
Underground storage tanks — fail to construct cover to prevent access |
14.2 (b) (i) |
$400.00 |
| 740. |
Underground storage tanks — fail to construct chain link fence to prevent access |
14.2 (b) (ii) |
$700.00 |
| 741. |
Underground storage tanks — fail to install a ladder inside the tank |
14.2 (c) |
$700.00 |
| 742. |
Underground storage tanks — fail to install a warning sign on the fence or cover |
14.2 (d) |
$400.00 |
| 743. |
Oil field fluid storage — fail to ensure fluid cannot create a hazard |
14.3 (a) |
$700.00 |
| 744. |
Oil field fluid storage — fail to ensure the storage area does not leak |
14.3 (b) |
$700.00 |
| 745. |
Oil field fluid storage — fail to construct a chain link fence around storage area |
14.3 (c) |
$700.00 |
| 746. |
Oil field fluid storage — fail to ensure all gates on fence are closed and locked |
14.3 (d) |
$400.00 |
| 747. |
Oil field fluid storage — fail to install prominent warning signs |
14.3 (e) |
$400.00 |
| 748. |
Oil field fluid storage — fail to install a ladder |
14.3 (f) |
$700.00 |
| 749. |
Oil field fluid storage — fail to install life-saving rescue equipment |
14.3 (g) |
$700.00 |
| 750. |
Fail to install a valve and piping on well before being serviced |
14.4 |
$400.00 |
| 751. |
Fail to cap a suspended well |
14.5 (a) |
$400.00 |
| 752. |
Fail to mark the site with well name |
14.5 (b) |
$450.00 |
| 753. |
Fail to plug the well when capable of flow to surface |
14.5 (c) |
$700.00 |